Yanmar Manual 3ym20
Water pump dripping, got the parts delivered now and about to strip out for rebuild. I know that at some time in the recent past I've seen a guide with tips to doing the rebuild and I'm sure it was on the forum somewhere. I've tried searching but can't find the post I'm after. Can anyone with a better memory point me in the right direction please. I'm not really concerned about starting the job without the guide but I seem to remember that there were some good tips that would be useful and it would be silly not read it again and avoid any pitfalls. Thanks Vic, it's not what I was looking for but no doubt will be handy for the future.
The exploded diagram on there has raised a question though, it only shows one seal on the shaft and I've been supplied with two 'oil' seals. No doubt all will become clear when I strip it down.If its a belt driven pump as shown in the manual there will only be one seal.
Yanmar 3ym20 Manual Download
If its mounted on the engine and directly driven from within then there will be two seals as GM describes. Odd that that there is this discrepancy / variation for the same engine but there you go.
Actually I dont think GM has a 3ym20 in his Mirror Usually they have a VP MD1 Check the bearings too! Last edited by VicS; 05-09-15 at 20:12. Have a look at YOUTUBE, there are some videos on there, not particularly for that pump but they give some good guides as to how to get bearings on/off. You will need to mark where the bearings need to go on the shaft and press them on from the 'corect' direction so as not to score the part of the shaft where the seals sit. That is if you are replacing bearings. When I re-built my pump a few months ago, I found that the bearing on the 'salt water side' disintegrated when I tried to remove it - presumably damaged by water getting past the seal. Worth doing the bearings whilst when you are in there!
Last edited by alan; 06-09-15 at 10:25. Reason: should have read replacing bearings not seals. Thanks for all the input. I have managed to find an article on doing the job on a similar pump (volvo) which has given me more information but is not identical.
It suggests replacing the springs in the seals with correctly sized o rings to stop the corrosion issues so I may do that if my o ring kit has the right size rings in it. I'll also look on u-tube before I start and see what it's got to offer. Vic, I think you're right - my pump is belt drive so will only have one seal not two.
Anyway, I've got 2 seals, 2 bearings, a new shaft and new impellor. Hopefully I won't need anything else. Just need to find the time to get to the boat and get started. Yet another accidental deletion - IS IT ONLY ME? AAAAAAARGH What I said was Sorry chaps, I should have read the question as my erstwhile maths teacher used to say.
I was describing what I did on my md1 engine which is direct drive and not belt drive. This has 2 seals and no ball bearings. One tip for the Opie is to examine the seals that have been supplied and reject them if they don't have stainless steel Springs. Suitable sales are on easily available from any bearing outlet and can be obtained with stainless Springs.
Yanmar Manual Download
Manual Covers: 1.FOR YOUR SAFETY 1.1 Warning Symbols 1.2 Safety Precautions 1.3 Warning Labels 2. PRODUCT EXPLANATION 2.1 Use, Propulsion System, Etc. 2.2 Engine Specifications 2.3 Names of Parts 2.4 Major Service of Parts 2.5 Control Equipment 2.5.1 Instrument Panel 2.5.2 Controls and equipment 2.5.3 Meters 2.5.4 Alarm equipment (lamps and buzzer) 2.5.5 Normal action of alarm devices 2.5.6 Single Lever Remote Control Handle 2.5.7 Shut-down Equipment 3. OPERATION 3.1 Fuel Oil, Lubricating Oil, and Cooling Water 3.1.1 Fuel Oil 3.1.2 Lubricating Oil 3.1.3 Cooling fresh water 3.1.4 Handling of Coolant 3.2 Before Initial Operation 3.2.1 Supply Fuel Oil 3.2.2 Supply Engine Lubricating Oil 3.2.3 Supply Marine Gear Lubricating Oil 3.2.4 Supply Cooling Water 3.2.5 Cranking 3.2.6 Check and Re-supply Lubricating Oil and Cooling Water 3.3 Operating your engine 3.3.1 Daily Start Up Inspection 3.3.2 How to Start the Engine 3.3.3 Operation 3.3.4 Cautions During Operation 3.3.5 Engine shut-down 3.4 Long Term Storage 4. MAINTENANCE AND INSPECTION 4.1 General Inspection Rules 4.2 List of Periodic Inspection Items 4.3 Periodic Inspection Items 4.3.1 Inspection on Initial 50 Hrs. Of Operation (or after 1 Month) 4.3.2 Inspection Every 50 Hrs.
(or Monthly) 4.3.3 Inspection Every 100 Hrs (or six months). 4.3.4 Inspection Every 150 Hrs (or one year). 4.3.5 Inspection Every 250 Hrs (or one year).
4.3.6 Inspection Every 1000 Hrs (or 4 years). 4.3.7 Annually 4.4 EPA Requirements 4.4.1 EPA Certification Plate 4.4.2 Conditions to Insure Compliance with Emission Standards 4.4.3 Inspection and Maintenance 5. TROUBLE AND TROUBLESHOOTING 6. PIPING DIAGRAMS 7. WIRING DIAGRAMS And More File Format: PDF Compatible: All Versions of Windows & Mac Language: English Requirements: Adobe PDF Reader & WinZip.
2017 harley davidson road king cvo owners manual. 2013 Harley Davidson Road King CVO FLHRSE5 Service Shop Manual On CD. 2017 Harley touring road king electra street glide ultra flt flhr owners manual. Access to the Owner's Manual for your bike, anytime. See which services your Harley® motorcycle needs and when, to keep it tuned and running its best.